- #Sn soti pocket controller pro for blackberry how to#
- #Sn soti pocket controller pro for blackberry install#
- #Sn soti pocket controller pro for blackberry portable#
- #Sn soti pocket controller pro for blackberry password#
- #Sn soti pocket controller pro for blackberry download#
On the Systems tab, tap Pocket Controller Enterprise. Figure Start Pocket Controller on the PDA by tapping Start, Settings. Disconnect the USB cable from the laptop and the instrument.
#Sn soti pocket controller pro for blackberry install#
Click Tools, Install Device Software, then follow the instructions for loading the Pocket Controller software to the PDA. Click on Guest Partnership and Next to continue. Connect the instrument s DATA port to the laptop via USB cable. Load Pocket Controller from the laptop to the instrument as follows: Figure 2. To be certain that the changes to the wireless controller settings are applied, restart the PDA. On the Wireless tab in the Networks to access pane, select All Available.
NOTE If you have previously set up the PDA to communicate to the laptop in a peer-to-peer network (Section II below), you must first return the PDA s wireless configuration to its original condition by tapping Start, Settings, Systems tab, Wireless Networks, Network Adapters tab, IEEE b WLAN Adapter, then set Use server-assigned IP address. Your network administrator might be able to assist with this. Next, tap the network you wish to connect to, then the Authentication tab, and enter the appropriate settings.
#Sn soti pocket controller pro for blackberry password#
If connecting to a network that requires a password, you can set the password on the PDA by tapping Start, Settings, the Systems tab, and Wireless Networks. Verify that the PDA is connected to the local network, for example, by running Internet Explorer and browsing to a known functional web page. Turn on the instrument PDA's wireless transmitter. Setting Up A Remote Access Point Protocol Using an Existing LAN A. Please contact your account manager or local ORTEC representative for this service.Ģ I. NOTE ORTEC Technical Support can arrange to set up your instrument for either of these configurations as either a return-to-factory, on-site, or telephone-supported procedure. Assigned IP addresses remain constant in the peer-to-peer configuration.
The peer-to-peer setup is slightly more complicated but is more secure and can be used independent of any other network support that is, it requires no additional infrastructure. Note: When using a LAN, the PDA can acquire a different IP address each time it connects, even if connecting to the same LAN. This might not always be the case, for instance, in field operations or might not be desirable for some missions due to security reasons. However, it has two requirements:! The PDA IP address must be reentered any time a new IP address is acquired by the instrument s PDA.! An open-access wireless LAN must be available through which the PDA and laptop can connect. The remote access point connection is easier to set up.
#Sn soti pocket controller pro for blackberry how to#
Section III tells how to switch from peer-to-peer to the remote-access-point protocol. Peer-to-peer requires only the instrument and the laptop see Section II. The remote access point configuration requires a wireless LAN to be available with which the PDA and the laptop can connect see Section I below. Remote Access Point or Peer-to-Peer Connection? Before proceeding further, you must decide whether to use a remote access point or peer-to-peer connection.
#Sn soti pocket controller pro for blackberry download#
ActiveSync is available as a free download from the Microsoft website or you can use the version on the CD accompanying the instrument. Before setting up the interface, you must install and configure Microsoft ActiveSync on both the laptop and the instrument s PDA. Commercial off-the-shelf software, Pocket Controller-Enterprise from SOTI, must be purchased to implement this approach: The Pocket Controller-Enterprise software allows you to both view the instrument display and operate the instrument from a remote laptop (within the limits of IEEE b) using the laptop s mouse instead of the instrument touchscreen.
#Sn soti pocket controller pro for blackberry portable#
1 Detective Family HPGe-Based Portable Nuclide Identifiers Wireless Remote Operation With SOTI s Pocket Controller Software This document tells how to set up the Detective-EX/DX, Micro-Detective, Micro-trans-SPEC, and trans-spec-dx-100 (hereinafter referred to as the instrument ) for remote wireless operation using the IEEE b protocol.
0 kommentar(er)
